Click here to go to the home page   APPLICATIONS   PRODUCTS    SUPPORT   CONTACT    SEARCH
 
Digital Video Receiver

Palladium Digital Video RX

The Palladium Pd-RX-XX integrates all the electronics required for RF reception, MPEG 2 decoding, COFDM demodulation and down converters into one small, milled aluminum housing. All connections are from the front panel. An optional IP interface board with Ethernet connection is available which mounts directly to the receiver. It is an ideal stand alone system for the reception of digital video in many applications.

The front panel of the unit provides two RSSI indicators, one for each antenna/receiver chain. Eight preset channel configurations may be selected. A ten pin Hirose connector is used for programming, remote on/off control, and power input. SMA connectors are used for the two antenna connections. A BNC connector is used for the standard video output, while a separate connector provides digital video loopthrough capability for a repeater mode. There are two adudio connectors.

The standard system operates at 2.5 MHz channel spacing with approximately 400 carriers. An optional model enables the decoding of both the 2.5 MHz (narrowband) data stream as well as DVB-T compliant mode data at 6, 7 or 8 MHz channels. End to end latency across the communications link is only 43 mS
in the narrowband mode, providing the ability to control a robot or UAV in near real time.

 

Features

  • Narrowband operation at 2.5 MHz for optimal frequency utilization
  • DVB-T compliant using 2000 carriers
  • Optional version demodulates both narrowband and DVB-T compliant transmissions
  • 43 mSec latency across the link in Narrowband mode
  • Diversity reception reduces multipath and fade impact
  • Maximal Ratio Combining for improved sensitivity
  • Internal AES 128 encryption
  • Low power consumption makes it ideal for integration into
    portable devices
  • Both NTSC and PAL supported
  • Optional IP interface board for streaming video over the Internet
  • Two high fidelity audio channels with variable sampling rates

 



 




Digital Video TX/RX Kit

Palladium Digital Video TX/RX Kit

The Palladium Digital Transmitter and Receiver Kit includes everything you need to transmit and receive high-quality video using the most advanced digital technology. Simply connect your video source or camera to the transmitter input and follow the simple Quick Start instructions for connecting antennas and power.

This kit is ideal for use inside buildings, in urban areas, and in other applications where multipath would normally cause video tearing or breakup. Kit components include the Palladium 100 Transmitter, Palladium Receiver, two magnetic mount receiver antennas, a dipole transmitter antenna, batteries, cables, and
connectors.

The Palladium digital video transmitter provides exceptional video quality in high multipath environments. The transmitter and receiver are designed for spectrum-efficient 2.5 MHz channel spacing. Approximately 400 carriers are used to transmit video and two channels of voice and data. Palladium transmitters may be located on adjacent channels without a guard band. AES 128-bit encryption ensures users of secure communications.

 

Features

  • Palladium COFDM Digital Technology
  • Palladium Digital Receiver
  • TX power output of 100 mW or 250 mW
  • Two audio channels and one data channel
  • Operating Frequency:
    L1 (1150 - 1400 MHz)
    L (1710 - 1850 MHz)
    S2 (2200 - 2300 MHz)
    S (2350 - 2500 MHz)
  • AES 128 bit Encryption
  • Optional 256 bit encryption
  • Battery Pack
  • Palladium Digital Receiver
  • Optional 2 Magnetic Mount Antennas
    High Gain Collinear Antennas
  • Dipole Antenna

 

 

 

 

 

 

     BACK TO TOP

 

 

DTC Communications
486 Amherst Street
Nashua, NH 03063

800-233-8639
www.dtccom.com

© 2006 Copyright DTC Communications, Inc. All Rights Reserved

ABOUT DTC

PRODUCTS

APPLICATIONS

RFQ

LINKS